Windshield Wiper Motor (Revised)

FYI - This is our 200th posting.
While I wait for dash parts I thought I'd check out the windshield wiper motor.  I bought this motor months ago on eBay.  The motor was sold as a core in unknown condition.  I got it cheap and I intended to have it rebuilt.  A rebuilt 1963 wiper motor without core can go for $500 to $600.

It looks dirty but other than that...

I opened it up out of curiosity and found good looking internal.  The grease was old but everything looked pretty good.  So I grabbed a 12 volt battery and tried to make it run.  Success!  Both speeds! 

Using carburetor cleaner I was able to remove all of the old grease.  Surprisingly, the gears and other mechanism look like new.

The windshield washer pump end cap has a hole in it so it's toasted.   But this part is easy to replace.  I removed the working parts and cleaned them as well.  Everything was re-assembled with waterproof silicone grease.  

I cleaned the outer case and stamped steel parts using crushed walnut shells in my blast box.  I masked the parts then applied a fresh coat of paint.

All I need is a missing rubber boot behind the wiper arm and...

I need the end cap for the washer pump.  Other than that, this thing is done.

With the money saved I think I'll shop for a clock for the dash.  The one I have died a horrible death in Hawaii.  The salt air destroyed it.  Yeah, maybe a clock...

POST SCRIPT

Turns out this wiper motor does not fit a 1963 Corvette. A 63 has 4 mounting positions, not 3 as shown.  So, watch for a future posting as I try to get this sorted out.  Dennis K and I will have a booth at the Portland Swap Meet this year.  You can bet this motor will be on the table.  

POST POST SCRIPT
By popular demand, the clock that died a horrible death.  This is all that's left:

  

Dash Cluster

Here is our 63 dash cluster shortly after the gauges were removed.

Everything below was done twice.  The first time I used rattle can paint which had ugly results.  The paint was too thick, too shiny and the masking tape left marks.  I sandblasted everything off then started again. 

The bezels, simulated leather backing, outer trim, switch receptacles and lettering are one piece of aluminum.  There are no pieces.  In this picture I taped off the simulated leather backing then spray painted the same House of Kolor 2 part epoxy primer I used on the car.  

All the bezels were sanded smooth.  You can see where the primer filled in the pot marks and blemishes.  This gets another coat to make sure all the metal has primer.  But first...

I need to prep the back side for paint.  This area was painted light green at the factory.  I believe this is what gives the gauges a green glow at night.  The color is close to our primer so I'll just use that. 

This is after the second coat of primer.  It has already been sanded smooth.

Next is two coats of primer sealer.  This will keep the final color from turning dull over time.  

The backside turned out very nice.

To simulate chrome I used House of Kolor silver striping paint with a hardener.  I also used a reducer so I could shoot it with an airbrush.  3 full coats were used then allowed to dry and harden.

 

The masking tape was removed from the simulated leather backing then I masked everything that I wanted to stay silver.   I taped over all the openings so that the back side wouldn't get painted.

The semi-gloss paint I used previously was too glossy.  I tried some satin black but it also was too glossy.  I decided on Eastwood's Rust Encapsulator, the same paint I used on the frame.  The finish is perfect and it should be able to stand-up to a lot of key abuse.  I airbrushed around the bezels to insure good coverage up against the silver then I used a regular HVLP spray gun to insure uniformity.  The texture and gloss is exactly what I wanted.

Before the black paint dried I used an eraser on the raised lettering.  That removed the black and exposed the silver beneath.  It turned out very nice.  Click on the picture and check it out.

Now all I have to do is stuff the cluster with this.

Thanks for watching.