Translate

Sunday, April 28, 2013

First Test Drive Repairs

After last weeks test drive I found a few things that need attention.  This includes soft brakes, loose trailing arm shims and this little jewel, a detached speedometer needle.


It took 3 hours to remove the steering column and dash, push the needle back on, then reattach all the dash wires, switches and cables and reinstall the steering wheel.  It's all done.  Whew...


The gas gauge wasn't working because of  a bad sending unit.  That requires the tank to be siphoned.


Then the spare tire tub has to be removed.


I already had a spare unit, the one is in the foreground.  It came with a new o-ring and locking ring.  I replaced everything.  The fuel gauge works fine now.


The brakes were soft.  I checked the National Corvettes Restorers web site to see if there was a trick to bleeding the brakes.  The most recommended solution was either to open the bleeders and use gravity or pressurize the master cylinder.  A vacuum pump was not recommended.  I decided to pressurize the master cylinder (shown). 


I built a simple plastic lid with an air fitting.  I added a large flat washer as reinforcement.


A standard clamp held the cap in place.  It only took about 5 psi to get the brake fluid moving.  There was a large air bubble in the left rear caliper.  The brakes are much better now.


I found loose trailing arm shims at both trailing arm locations.  My shop manual says the shims have to be packed tight then t torqued to 60 foot pounds.  They're tight now.


Here is one of the shims.


They get stacked side by side and go on both sides of the trailing arm. This view is from the front of the rear tire looking up.


If you haven't guessed, I took the Corvette out for another test ride this weekend to verify everything above.  All is well but I did find a new issue.  The right side of the engine is leaking oil at the #2 spark plug.  I called Matt P. and he recommended I put thread sealer on all the head bolts and exhaust manifold bolts.  That's a job that I will address in the next post.


So, instead of ending on a sour note I thought you'd like to see the headlights in action.  Check them out in this video.  A special thanks to Ty for restoring the headlight buckets a few years ago.  They work great. 









Sunday, April 21, 2013

Dash, Headlights and Wiring

I accomplished a lot of things this week.  It started with the installation of a new speaker.


I re-painted the speaker grill with Por-15 Chassis Coat Black.  It's satin and turned out very nice.


The clock was re-installed using 2 special clips.  They hold the clock and insure proper grounding.


I purchased a new glove box (upper left).  All the metal components were media blasted and painted with Por15.  The glove box door is unique to 1963 and ours is original but it's condition is horrible.  It can't be saved, at least not by me.  I'll be watching for a better one.  


Our 1963 door has missing pieces, holes drilled at the top, cracks and scratches everywhere.


I installed the glove box and frame then remembered...


I have a 64 (or later) door that didn't sell at the Portland Swap Meet.  I reconditioned it with Por15 and installed it temporarily.  It's not a 63, it has a couple dents, but it will do for now.


Not too bad.


I installed the windshield washer spray heads and used Rivet Nuts to fasten the wiper grills.


I coupled the Flaming River steering column to the steering box with a beautiful polished stainless steel universal joint.  The spline counts will vary by year.  Mine is a 3/4" 36  X 3/4" 36.  It took me too tries to get it right.


Here is a better picture of the blinker and tilt levers I modified to make look like  original.


The headlight wiring harness was finally installed.  I had to remove the grill and bumpers for access.    In this picture you can see the running lights are now working. 


 Viewed from below are the two headlight bucket motors.  They are installed and wired.


Also installed are the two horns.  GM horns in the 60's were identical between most models.  The difference is the bracket and orientation of the horn.  An original set of working horns for a 1963 fuelie would set you back about $1500, but you can't find them.  Mine are from a Skylark.  The horns sound like a 63 Corvette, they're orientated properly, but the mounts are slightly different.  I am good with it.



I also installed the headlights.  Here they are tucked up under the nose.


Here they are in the open position.  Ty had spent a lot of time refurbishing these so they were simple to install.  They still get bezels but they're not yet painted.


So, after all of this work, do you know what time it is?  Check out these videos.