Door Windows and Electronic Ignition

I put off the side window installation because I thought it was going to be difficult.  I was right.  It took 10 hours and multiple attempts before I finally finally figured out the correct sequence.  The door goes together like a Chinese puzzle box.  You may get most of the pieces installed but there seems to always be at least one piece left over.  For those that might be visiting this site to find the proper sequence, I'll be a little more detailed than usual.  There may be other ways, this is my way.

I polished the glass and installed new rubber molding.  I rebuilt both geared wing window mechanisms and the main side window actuators.  Lithium grease was used on all moving parts.

The first piece installed is the main side window actuator including the small track shown in the lower left of the picture.  After this is installed crank it down as low as it will go.

Next is the wing window chrome molding and the wing window, in that order.

The chrome molding can be held in place with tape.

The wing window and chrome  are fastened with 4 screws located under the door weather striping.

Next is the window channel.  This is held in place with push snaps only.  For now, the lower pig tail will hang loose.  This is a key step, it must be loose otherwise the window will not fit in the door.

Next the window is lowered into the door.  Hold the rear of the window a little higher than the front otherwise it won't fit.  Once it's inside the door put it in the window channel then push it all the way up.  I used duct tape to hold it in place.  Now roll the window actuator up so the rollers can be installed in the window track.  There are strategically placed holes in the upper part of the door that allow access to the nuts. 

The final piece is the lower rear tract channel.  You'll need patience for this one.  When installed, the pig tail goes in the channel and gets fastened with a sheet metal screw near the bottom.  That's it.

Both sides are done and the windows did add some weight to the doors.

The doors shut even better now.  They're very solid.

I also replaced the points with this electronic ignition kit.  It took about an hour and it works great.  No more filing points, setting gap or adjusting dwell.  

  

That's it.  Thanks for watching.

Interior Trim, Door Sills, Glove Box Door and a Distraction

I spent the last couple weeks with family in Wisconsin.  Max H reminded my wife that I have an obligation to my blog followers and I need to provide an update soon.  Here you go Max!

The interior trim was primered, sanded, then primered again on all sides. 

All sides were painted with Por15, the same paint I used on the speaker grill and dash cluster.  I'll let this dry for several days before I start assembly.

Door sills are usually fastened with sheet metal screws.  I decided to use Rivet-Nuts instead.

The door sills look great and really add to the finish of the interior.

The coil wire now has 90 degree caps.  The distributor and coil are ready for radio shielding.

But first I need properly made mounting brackets.  The reproduction on the left has a mounting plate installed incorrectly.  The one on the right is correct.  Errors like this are not uncommon with reproduction pieces.

Same thing for this bracket.  The one on the top is correct.  The one on the bottom is incorrect.

The radio shielding is very difficult to install.  It's no wonder most of these were removed and never reinstalled.  The remaining shielding I have is incorrect for a 63.  That will be added to my to-do list.

I have 4 used glove box doors.  None are of the same quality as our build.  This is the best one I have but it's for a 64 Corvette and it has a few blemishes.  I am not tickled with it.

Gerri bought me a new Trim-Parts 1963 glove box door for my birthday.  How sweet is that?
It looks much better and I feel much better!

A NEW DISTRACTION

While in Wisconsin I picked this up.  Anybody know what type of bike this is?

It's my new distraction.  Come on guys, you know what this is.

CDN 2013 Update:  I believe I am still on track for Cool Desert Nights.  I need the seats upholstered and the side windows installed.  Al Knoch Interiors still owe me seat parts from over a month ago.  If anything is going to be iffy it will be the seats.  Wish me luck!